- 您现在的位置：买卖IC网 > Sheet目录311 > AS5140 PB (ams)BOARD PROGRAM AS5140
AS5140H
Data Sheet - P i n A s s i g n m e n t s
Table 1. Pin Descriptions
Pin Name
PWM_LSB
NC
NC
VDD3V3
VDD5V
Pin Number
12
13
14
15
16
Description
Pulse Width Modulation of approx. 1kHz; LSB in Mode3.x
For internal use. Must be left unconnected.
For internal use. Must be left unconnected.
3V-Regulator Output (see Figure 17)
Positive Supply Voltage 5V
Pins 1 and 2 are the magnetic field change indicators, MagINCn and MagDECn (magnetic field strength increase or decrease through variation
of the distance between the magnet and the device). These outputs can be used to detect the valid magnetic field range. Furthermore those
indicators can also be used for contact-less push-button functionality. Pins 3, 4 and 6 are the incremental pulse output pins. The functionality of
these pins can be configured through programming the one-time programmable (OTP) register:
Table 2. Pin Assignment for Different Incremental Output Modes
Output Mode
1.x: Quadrature
2.x: Step/direction
3.x: Commutation
Pin 3
A
LSB
U
Pin 4
B
Direction
V
Pin 6
Index
Index
W
Pin 12
PWM
PWM
LSB
Mode 1.x: Quadrature A/B Output
Represents the default quadrature A/B signal mode.
Mode 2.x: Step / Direction Output
Configures pin 3 to deliver up to 512 pulses (up to 1024 state changes) per revolution. It is equivalent to the LSB (least significant bit) of the
absolute position value. Pin 4 provides the information of the rotational direction.
Note: Both modes (mode 1.x and mode 2.x) provide an index signal (1 pulse/revolution) with an adjustable width of one LSB or three LSB’s.
Mode 3.x: Brushless DC Motor Commutation Mode
In addition to the absolute encoder output over the SSI interface, this mode provides commutation signals for brushless DC motors with either
one pole pair or two pole pair rotors. The commutation signals are usually provided by 3 discrete Hall switches, which are no longer required, as
the AS5140H can fulfill two tasks in parallel: absolute encoder + BLDC motor commutation. In this mode,
- Pin 12 provides the LSB output instead of the PWM (Pulse-Width-Modulation) signal.
- Pin 8 (Prog) is also used to program the different incremental interface modes, the incremental resolution and the zero position into the
OTP (see page 21) . This pin is also used as digital input to shift serial data through the device in Daisy Chain configuration, (see page 14) .
- Pin 11 Chip Select (CSn; active low) selects a device within a network of AS5140H encoders and initiates serial data transfer. A logic high
at CSn puts the data output pin (DO) to tri-state and terminates serial data transfer. This pin is also used for alignment mode (see page
22) and programming mode (see page 19) .
- Pin 12 allows a single wire output of the 10-bit absolute position value. The value is encoded into a pulse width modulated signal with 1μs
pulse width per step (1μs to 1024μs over a full turn). By using an external low pass filter, the digital PWM signal is converted into an ana-
log voltage, allowing a direct replacement of potentiometers.
www.austriamicrosystems.com/AS5140H
Revision 1.4
5 - 37
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
ASDMB-ADAPTER-KIT
ASDMB MEMSPEED P II OSC KIT
ASFLMPLP-ADAPTER-KIT
ASFLMPLP MEMSPEED P II OSC KIT
AT24C01-10SI-1.8
IC EEPROM 1KBIT 400KHZ 8SOIC
AT24C01B-TSU-T
IC EEPROM 1KBIT 1MHZ SOT23-5
AT24C02C-XHM-B
IC EEPROM 2KBIT 1MHZ 8TSSOP
AT24C04AN-10SI-2.7
IC EEPROM 4KBIT 400KHZ 8SOIC
AT24C08B-PU
IC EEPROM 8KBIT 1MHZ 8DIP
AT24C1024B-TH25-B
IC EEPROM 1MBIT 1MHZ 8TSSOP
相关代理商/技术参数
AS51400FLF
制造商:TT Electronics / IRC 功能描述:AS51400FLF
AS51400HLF
制造商:TT Electronics / IRC 功能描述:AS51400HLF
AS51400JLF
制造商:TT Electronics / IRC 功能描述:AS51400JLF
AS51401FLF
制造商:TT Electronics / IRC 功能描述:AS51401FLF
AS51401HLF
制造商:TT Electronics / IRC 功能描述:AS51401HLF
AS51401JLF
制造商:TT Electronics / IRC 功能描述:AS51401JLF
AS51402FLF
制造商:TT Electronics / IRC 功能描述:AS51402FLF
AS51402HLF
制造商:TT Electronics / IRC 功能描述:AS51402HLF